AEG Lavamat error codes

Here are AEG Lavamat service error codes:

error code

sub
code

AEG error code definition

washing machine problem solution

Solution through white goods engineer

error code
E10

E11

No water supply to washing machine

water tap, filter (screen) clean

Electronics / valve / connection cable / pressure switch / replace luchtval

E13

Too little water in washing machine

Check valve, supply hose and hose correctly explain (kink in the hose), filter cleaning.

Valve / inlet hose / pressure switch replaced / hydraulic control circuit.

error code
E20

E21

No drainage from the washing machine

Filter check for foreign objects, drain control, hose, tube blockage.

Pump / pressure switch / pressure sensor / electronics replaced

E23

Pump / electronics washing machine problem

Supplier of bubble machine

Pump / electronics / tire pump cables replaced

E24

Measuring Circuit

Call supplier

Replace electronics

Error Codes
E30

E31

Pressure washing machine problem

Call supplier

Pressure sensors / flat cable replaced

E32

Pressure sensor gives a message

Water tap, filter check for objects.

Valve / luchtval / pressure sensor replaced

E33

Pressure sensor problem

Call supplier

Pressure switch / pressure sensor / tape / cable luchtval / heating / electronics replaced

E34

Pressure sensor problem

Call supplier

Pressure sensor / tape / cable replacement luchtval

E35

Safety message in washing machine

Call supplier

Pressure switch / pressure sensor / tape / cable luchtval / electronics / replace hydraulic control circuit.

E36

Measuring circuit problem

Call supplier

Replace electronics

E37

Measuring circuit problem

Call supplier

Replace electronics

E38

Pressure switch problem

Call supplier

Luchtval cleaning / replacement

E39

Pressure switch problem

Call supplier

Replace electronics

E3A

heater relay problem

Call supplier

Replace electronics

error
E40

E41

Open lid, locking machine malfunction.

Lock control, where defective: Call dealer

Locking / link / cable replacement electronics

E42

Defective locks, open during wash / will not open at the end wash.

Call supplier

Locking / link / cable replacement electronics

E43

Triac (power circuit) locking of machine breakdown

Call supplier

Locking / link / cable replacement electronics

E44

Measuring Circuit locking

Call supplier

Replace electronics

E45

Measuring Circuit locking

Call supplier

Replace electronics

error
E50

E51

motor triac (power circuit) circuit

Call supplier

Electronics / flat cable replaced

E52

Engine failure blockade / tachometer (rotation meters) interruption / motor ribbon cable defective.

Call supplier

Tachometer / engine / tire / cable electronics replaced

E53

Measuring Circuit engine

Call supplier

Replace electronics

E54

Engine failure relay

Call supplier

Replace electronics

E55

Motor circuit is interrupted

Call supplier

Motor replacement / flat cable check

E56

Adjournment tachometer (rotation meters)

Call supplier

Tachometer replaced

E57

Total current greater than 15A

Call supplier

Engine / engine electronics / flat cable replaced

E58

The flow of a phase larger than 4.5 A

Call supplier

Engine / link / cable replacement engine electronics

E59

no tachometer signal (rotation meters) to the engine

Call supplier

Tachometer / engine / tire / cable electronics replaced

E5A

heatsink temperature exceeds 88 degrees

Call supplier

Engine electronics module

E5B

Voltage below 175 Volts

Call supplier

Electronics Engine / flat cable replaced

E5C

Voltage exceeding 430 Volts

Call supplier

Engine electronics module

E5D

Data transmission problem

Call supplier

flat cable replaced

E5e

Communication error engine electronics

Call supplier

Replace electronics

E5F

Engine Electronics fault

Call supplier

Electronics / engine electronics / flat cable replaced

error code
E60

E61

Does not heat, heating or NTC defective.

Call supplier

NTC / heating / flat cable replaced

E62

Superheat temperature exceeding 88 degrees

Call supplier

NTC / heating / flat cable replaced

E66

Heating relay defective.

Call supplier

Dry running protection 1 / 2 dry run protection / link / cable replacement electronics

E68

Excessive flow diversion

Call supplier

Heater or other parts inside

E69

Does not heat, voltage> 5Volt

Call supplier

Heater / flat cable replaced

error code
E70

E71

NTC (temperature sensor) is defective.

Call supplier

NTC / tape / cable electronics replaced

E74

NTC is not the right place

Call supplier

Mounting position NTC control

error
E80

E82

Wrong reste-position program switch

Call supplier

Replace electronics

E83

Read error program switch

Call supplier

Wrong configuration, replace electronics

E84

Measuring circuit circulation pump

Call supplier

Replace electronics

E85

Circulating pump failure

Call supplier

Circulation Pump / electronics replaced

error
E90

E91

Error in communication electronics

Call supplier

E / A electronics / belt / cable electronics replaced

E92

Inequality in electronics

Call supplier

E / A electronics fit to head electronics

E93

Incorrect configuration

Call supplier

Replace electronics

E94

Incorrect configuration wash

Call supplier

Replace electronics

E95

communication error

Call supplier

Replace electronics

E96

no consensus in hardware version of the configuration

Call supplier

Replace electronics

E97

no consistent program and switch configuration

Call supplier

Replace electronics

E98

disagreement engine electronics and other electronics

Call supplier

Electronics / flat cable replaced

E99

in-/uitgave electronics speaker problem

Call supplier

Speaker / flat cable replaced

E9A

Speaker firmware problem.

Call supplier

Import / editing electronics replaced

E9F

communication error between the engine electronics and other electronics

Call supplier

Electronics / flat cable replaced

error code
EA0

Ea1

DSP failure

Call supplier

DSP / tire cord / belt / electronics replaced

EA2

DSP reports failure

Call supplier

Replace electronics

EA3

DSP engine pulley can not block.

Call supplier

DSP / ribbon cable / electronics / belt replaced.

EA4

DPS defect

Call supplier

DSP / electronics / flat cable replaced

EA5

Triac DSP failure

Call supplier

Replace electronics

EA6

Drum blocked in 3 to 30 seconds

Call supplier

DSP replacement, belt replacement, drum lid has been opened.

error code
EB0

EB1

Frequency outside limits

Voltage power mains wrong / insane. If correct: call vendor

Replace electronics

EB2

Mains voltage too high

Voltage mains socket faulty / degraded. If correct: call vendor

Replace electronics

EB3

Mains voltage too low

Voltage mains socket faulty / degraded. If correct: call vendor

Replace electronics

EBE

Defective safety relay control panel

Call supplier

Replace electronics

EBF

Cycle control circuit of the safety relay is defective.

Call supplier

Replace electronics

error
EC0

EC0

Valve blocks

Call supplier

Valve / electronics / flat cable replaced

EC2

Dirt level sensor malfunction

Call supplier

Sensor replaced

error
EF0

(EFO)

see top of this page!

EF1

Screen lint clogged, clogged afvoerdam

Lint Screen / afvoerdam cleaning

-

EF2

Overdoses foam during pumping, lint screen clogged, clogged afvoerdam

Not overdosing on lint screen / cleaning afvoerdam

-

EF3

Aqua Control system mobilized / ribbon cable defective pump / pump failure

Call supplier

Leak in appliance repair / replace connection cable / pump.

EF4

No signal of flow sensor

encourage water / water control.

Flow Sensor blockade lifted.

EF5

Centrifugation is interrupted, imbalance greater than 1200 grams

At large loads watch / Placement of machine vibration and possible correction.

-

error code
EH0

EH1

Frequency outside the limit

Call supplier

Valve / electronics / flat cable replaced

EH2

Mains voltage too high

Voltage mains socket faulty / degraded. If correct: call vendor

Replace electronics

EH3

Mains voltage too low

Voltage mains socket faulty / degraded. If correct: call vendor

Replace electronics

EHE

Defective safety relays on the steering wheel panel

Voltage mains socket faulty / degraded. If correct: call vendor

Replace electronics

EHF

Cycle control circuit of the safety relay is defective.

Call supplier

Replace electronics

Taken from http://www.meolease.nl/AEG_wasmachine_foutcodes.htm and translated from Dutch.

Rubriky:

Komentáře

Eva
před rokem

Hi, don't know if you can give me advice but I hope you can.
I have a oko lavamat 86820 update washing machine and I am getting error code C2 and 1h.
The machine has stopped suddenly. There is water in the drum and I can't open the machine. Can you tell me what the cause can be and if it is a big problem to get fixed. I bought the machine approx. 10 yrs ago and has been working perfectly till now.
Kind regards
Eva

Avni
před 19 dny

I have an AEG 41230 and I am gettin error code E04.
The machine doesnt work.
Could you please help me,it would be very friendly.

*
*
Překročil(a) jsi maximální délku komentáře o 0 znaků.
*  captcha

Archive